Class 2 vs Class 3 Safety Vest: 4 Questions That Decide It (With OSHA Rules and Real Prices)
A Class 2 safety vest is the right buy for most warehouse, dock and yard crews, and it is the legal minimum for anyone working on foot inside a public road right-of-way. A Class 3 safety vest is the right buy when the worker faces faster traffic, works at night or in low light, or has to be seen from the side with arms down, because Class 3 is the only performance class that requires a reflective band around each sleeve. On Warehouse Gear Hub, a Pyramex RVZ40 Class 2 mesh vest is $6.90, the RVHL40 Class 2 breakaway vest is $8.61, the RVZ36 Class 3 mesh vest is $19.10, and the RRWP31 Class E rain pants that turn a Class 2 vest into a Class 3 ensemble are $27.46. The four questions below take you from the job to the part number, with the rule quoted from the 2023 MUTCD and from OSHA's own standards and letters, and every square inch and band width from ANSI/ISEA 107-2020 summaries published by 3M and Radians.
- Who is required to wear a Class 2 or Class 3 vest?
- Question 1: Will the vest be worn in a road right-of-way, in the yard, or inside the building?
- Question 2: How fast is the traffic, and how much light is there?
- Question 3: Does the worker need to be seen from the side with arms down?
- Question 4: What will the vest go through: snags, heat, cold, rain, sparks or arc flash?
- Which safety vest should you buy?
- Frequently asked questions
Who is required to wear a Class 2 or Class 3 vest?
Start with the one rule that names a class. Section 6C.05 of the 11th Edition of the Manual on Uniform Traffic Control Devices (MUTCD), December 2023, is a Standard, which in MUTCD language means a shall statement: "For daytime and nighttime activity, all workers, including emergency responders, within the right-of-way" who are exposed to traffic or to work vehicles and equipment "shall wear high-visibility safety apparel that meets the Performance Class 2 or 3 requirements of the ANSI/ISEA 107-2015" standard, and "A person designated by the employer to be responsible for worker safety" makes "the selection of the appropriate class of garment." The MUTCD has carried that requirement since its 2009 edition; the Federal Highway Administration set a compliance date of December 31, 2011 for the worker and flagger apparel provisions in the Federal Register, and the 2023 edition renumbered the text to 6C.05.
OSHA reaches the same place by two routes. 29 CFR 1926.201(a) states: "Signaling by flaggers and the use of flaggers, including warning garments worn by flaggers, shall conform to Part 6 of the MUTCD," which puts the Class 2 or 3 requirement in an OSHA standard for every flagger. 29 CFR 1926.651(d) states: "Employees exposed to public vehicular traffic shall be provided with, and shall wear, warning vests or other suitable garments marked with or made of reflectorized or high-visibility material." For everyone else in a highway work zone, OSHA's August 5, 2009 letter of interpretation concludes that because the struck-by hazard is recognized and high-visibility apparel is a feasible control, "high-visibility apparel is required under the General Duty Clause" of the OSH Act, Section 5(a)(1).
Inside a warehouse there is no OSHA sentence that says vest. 29 CFR 1910.132(d)(1) requires that "The employer shall assess the workplace to determine if hazards are present, or are likely to be present, which necessitate the use of personal protective equipment (PPE)," then "Select, and have each affected employee use, the types of PPE that will protect the affected employee" and "Select PPE that properly fits each affected employee." Paragraph (d)(2) requires "a written certification that identifies the workplace evaluated," and (h)(1) requires that PPE "shall be provided by the employer at no cost to employees." The written hazard assessment is where a warehouse decides, and documents, whether people on foot who share floor space with forklifts wear hi-vis, and which class.
Question 1: Will the vest be worn in a road right-of-way, in the yard, or inside the building?
This question settles the floor. If the worker will ever stand in a street or highway right-of-way exposed to traffic, the floor is Class 2 under MUTCD 6C.05, and the vest should be a Type R garment. 3M's summary of ANSI/ISEA 107-2020 defines the three garment types: "Type 'R' garments are for occupational workers who are exposed to roadway traffic," "Type 'P' garments give additional options for fire, police, and EMS personnel," and "Type 'O' garments are for occupational workers who are not required by the MUTCD 2009 edition to wear HVSA." Type O is Class 1 only. Type R and Type P come in Class 2 and Class 3. Every Pyramex vest on our site that lists a type lists Type R.
Who counts as a worker in the right-of-way is narrower than people assume. The FHWA's official MUTCD interpretation on delivery personnel says drivers making deliveries "would generally not perform a majority of their work within the right-of-way and be exposed to traffic," so they are generally not workers under the rule, and that "it is not practical to make blanket statements about a general class of personnel." A driver who gets out to stage freight at the curb for an hour is a different case from one who hands over a parcel, and the FHWA ties that call to the employer's own worker safety planning.
Inside the building and in a fenced yard, the MUTCD does not apply and the 1910.132(d) assessment decides. The ANSI category written for that setting is Type O Class 1, with the smallest material minimums in the standard. We do not stock a Class 1 vest, and for a buyer that is not a loss: a Type R Class 2 vest covers every case a Class 1 does, also satisfies the MUTCD minimum the moment the same worker steps onto a roadside, and costs $5.57 to $9.86 on our site. One SKU covers the dock, the yard and the curb.
Here are the minimums each class has to meet, per 3M's and Radians' summaries of ANSI/ISEA 107-2020. Background material is the fluorescent fabric; retroreflective material is the tape.
| Type and class | Background material, minimum | Retroreflective material, minimum | Band width, minimum | Written for |
|---|---|---|---|---|
| Type O, Class 1 | 217 sq in | 155 sq in | 1 in | Workers not required by the MUTCD to wear hi-vis; off-road, warehouses, yards |
| Type R, Class 2 | 775 sq in (540 sq in allowed on the smallest size only) | 201 sq in, no reduction for size | 1.38 in (1 in for split-trim designs) | Workers exposed to roadway traffic; the MUTCD minimum |
| Type R, Class 3 | 1,240 sq in (1,000 sq in allowed on the smallest size only) | 310 sq in, no reduction for size | 2 in | Workers exposed to roadway traffic; must have a band encircling each sleeve |
| Type P, Class 2 / Class 3 | 450 sq in / 775 sq in | 201 sq in / 310 sq in | 2 in | Fire, police and EMS; less background fabric than Type R |
| Class E (supplemental) | 465 sq in | 109 sq in | Encircles each leg | Pants, bibs, shorts and gaiters worn with a Class 2 or 3 top; not a class on its own |
Class 1 to Class 2 is more than three times the fluorescent fabric. Class 2 to Class 3 is another 465 sq in of fabric and 109 sq in of tape, which is exactly the Class E allotment, and that arithmetic is why a Class 2 vest plus Class E pants is treated as a Class 3 ensemble in Question 3.
Question 2: How fast is the traffic, and how much light is there?
Neither the MUTCD nor any OSHA standard sets a speed at which Class 3 becomes mandatory. MUTCD 6C.05 leaves the class to the person the employer designates, and its one class-specific instruction is Guidance, a should statement, that flaggers working at night should wear "high-visibility safety apparel that meets the Performance Class 3 requirements." The speed bands you will see in distributor guides, Class 1 under 25 mph, Class 2 for 25 to 50 mph, Class 3 above 50 mph, are rules of thumb from the trade, not text from a regulation. They are a reasonable starting point for a roadside hazard assessment, and the written assessment should say that is what they are.
Inside a warehouse the speed question answers itself. Our listing for the EKKO EK18RF stand-up rider forklift gives a travel speed of 12 km/h loaded, which is about 7.5 mph, and that is a quick truck for an aisle. Speed is not what puts a picker in the hospital. OSHA's Powered Industrial Trucks eTool tells pedestrians "The driver's visibility may be limited due to blind spots" and "Be aware of the wide rear swing radius," and tells operators to "Sound the horn at blind corners, doorways and aisles" and "Use a spotter for blind spots." A load on the forks hides the operator's forward view; the counterweight swings into the aisle on a turn. Hi-vis buys the operator the half second it takes to register a person at the edge of that view, and Class 2 does that job at walking-pace forklift speeds.
Light is the variable that moves warehouse crews up a class. Class 3 carries 1,240 sq in of fluorescent fabric and 310 sq in of tape against 775 and 201 for Class 2, per 3M. Fluorescent fabric does its work in daylight and loses it at dusk; retroreflective tape does its work in headlights and adds little at noon. A crew that is fine in Class 2 on a lit dock at 2 PM is working a different problem on an unlit yard at 5 AM in January, when the only thing a yard truck driver sees is tape. Night yard work, outdoor staging under sodium lights, winter shifts that start and end in the dark, and any roadside work after sunset are Class 3 cases, or Class 2 plus Class E.
Class 2 polyester mesh vest with 2 inch silver reflective material, contrasting trim and a zipper front, in lime or orange, sizes Small through 5X Large. Sold each. The hook and loop RVHL29 ($5.57) is the same class in solid polyester with no mesh, and the RCZ21 ($9.86) adds an X-back and a phone pocket and is also certified to CAN/CSA Z96-2015 Class 2 Level 2.
Question 3: Does the worker need to be seen from the side with arms down?
This is the design difference between the two classes, and it is the one most buying guides skip. Per 3M's summary, "Class 3 garments must have at least one retroreflective band encircling each sleeve." A sleeveless vest alone cannot be Class 3, however much tape is sewn onto it. Safety+Health magazine explains why the standard insists on it: a worker standing sideways to oncoming traffic with arms at the sides covers the tape and fabric on the torso with the arms, and the sleeve bands are what remain visible. The same article notes that a Class 2 vest, which has no sleeves, has to carry tape across the shoulders from front to back instead.
So a Class 3 "vest" is a short-sleeve garment. Pyramex's RVZ34 ($20.26) and RVZ36 ($19.10) are both rated Type R Class 3 on our listings, and a distributor listing of the RVZ36 describes the garment with "short sleeves, a zippered front." The sleeves are what carry the encircling bands and most of the extra 465 sq in of fabric. If a crew will not wear sleeves over a shirt in August, the alternative is a Class 3 long sleeve shirt or jacket worn as the hi-vis layer itself: the RLTS31 Class 3 long sleeve shirt is $121.04 for a pack of 5, and the RJ31 Class 3 waterproof bomber jacket is $78.77.
Type R Class 3 in lightweight polyester mesh, silver reflective bands with contrasting trim, zipper front, clear hook and loop chest pocket, 2 mic tabs, 4 outer pockets and 5 inch zippers on each side, in lime or orange, sizes Small through 5X Large. Sold each. The RVZ34 ($20.26) is the same class with a solid front, mesh back and 7 pockets.
The other route to Class 3 is the one the arithmetic in Question 1 set up. Class E garments add 465 sq in of fluorescent fabric and 109 sq in of tape on the legs, and Radians' summary states it in four words: "Class 2 + Class E = Class 3." Safety+Health quotes Tingley Rubber's senior product manager Brian Nutt to the same effect, that "the use of a Class 2 and Class E garment together are equivalent to the use of a Class 3 garment." A worker in a Class 2 vest and Class E pants shows tape on the legs from every angle, including sideways with arms down, which is the view the sleeve rule exists for. For a crew that already owns Class 2 vests, a pair of Class E pants or rain pants is the cheapest step up a class, and it is the right step in weather, since the pants are the layer you would be adding anyway.
Rated ANSI 107-2020 Type R Class E and waterproof with sewn and sealed seams, breathable polyester with a polyurethane coating, 2 inch silver reflective material, elastic waist, metal take-up snaps at the ankles and two outer pockets, in lime, sizes Small through 5X Large. Sold each, price per pair. The RRWB31 Class E rain bib is $52.88 and the RWB46 Class E insulated winter bib is $96.21.
Two cautions on ensembles. First, the class is a count of visible material, so a dark jacket or hoodie pulled over a Class 2 vest in cold weather hides the fabric the class depends on; in winter the hi-vis layer goes on the outside, which is what the RWVZ45 Class 2 insulated winter vest ($64.78) and the Class 3 jackets are for. Second, the garment label is the proof. Per PIP's summary of the 2020 revision, the label carries a pictogram showing the garment's Type and Class, and every garment that is not flame resistant must state: "This garment is not flame resistant as defined by ANSI/ISEA 107-2020." A vest with no such label is a non-rated vest, whatever color it is.
| Model we stock | Rating on our listing | Fabric | Closure | Reflective material | Sold as | Price as listed |
|---|---|---|---|---|---|---|
| Pyramex RV1 non-rated mesh vest | Non-rated | Polyester mesh | Hook and loop, elastic sides | 1 in vinyl | Pack of 12, one size | $77.95 per pack |
| Pyramex RVHL29 | Type R, Class 2 | Solid polyester, no mesh | Hook and loop | 2 in silver | Each, S to 3XL | $5.57 |
| Pyramex RVZ40 | Class 2 | Polyester mesh | Zipper | 2 in silver | Each, S to 5XL | $6.90 |
| Pyramex RVHL40 breakaway | Type R, Class 2 | Polyester mesh | Breakaway hook and loop at shoulders, sides and front | 2 in silver | Each, S to 5XL | $8.61 |
| Pyramex RVZ21, pack of 5 | Type R, Class 2 | Polyester mesh | Zipper | 2 in silver | Pack of 5, S to 5XL | $42.88 per pack |
| Pyramex RVZ36 | Type R, Class 3 | Polyester mesh, short sleeves | Zipper | Silver with contrasting trim | Each, S to 5XL | $19.10 |
| Pyramex RVZ34 | Type R, Class 3 | Solid front, mesh back | Zipper | 2 in silver with contrasting trim | Each, S to 5XL | $20.26 |
| Pyramex RVZ38BR breakaway | ANSI/ISEA 107-2020 Type R, Class 3 | Fitted cut, drawstring waist | 5-point breakaway hook and loop plus zipper | 2 in silver | Each, S to 5XL | $21.20 |
| Pyramex RVZ52FR arc-rated | Type R, Class 2; ATPV 4.0 cal/cm², ASTM F1506, NFPA 70E Category 1 | Modacrylic mesh | Zipper | 2 in FR silver | Each, S to 5XL | $79.90 |
| Pyramex RVZ53FR arc-rated | Type R, Class 3; ATPV 4.0 cal/cm², ASTM F1506, NFPA 70E Category 1 | Modacrylic mesh | Zipper | 2 in FR silver | Each, S to 5XL | $119.90 |
| Pyramex RRWP31 rain pants | ANSI 107-2020 Type R, Class E | PU-coated polyester, waterproof | Elastic waist, ankle snaps | 2 in silver | Each, S to 5XL | $27.46 |
Ratings, fabrics and tape widths are from our product listings; prices are Warehouse Gear Hub's as of this writing. Read the tape column against the standard's minimum band widths: 1.38 in for Class 2 and 2 in for Class 3. Every rated Pyramex vest above runs 2 in tape, and the non-rated RV1 runs 1 in vinyl, under the Class 2 minimum before you count a square inch of area.
Question 4: What will the vest go through: snags, heat, cold, rain, sparks or arc flash?
Class decides how much material the vest carries. What that material is made of, and how it comes off, depends on the job. Run through the hazards in order.
Snags. A vest that catches on a pallet rack, a conveyor or a forklift's overhead guard holds the wearer to it. A breakaway vest does the opposite: per our listing, the Pyramex RVHL40 "is built to tear away at the shoulders, sides and front if it catches on moving equipment," with hook and loop closures that "open along the shoulders, both sides and the front, so the vest can come off in a pull." That is the vest for pickers working alongside forklifts and for anyone leaning into a trailer. The RCA25 ($12.64) adds an X-back, an adjustable waist and a reinforced D-ring slot for a fall-protection lanyard; the RVZ38BR ($21.20) is the Class 3 version with 5-point breakaway closures.
Type R Class 2 in breathable polyester mesh on a fluorescent lime background, breakaway hook and loop closures at the shoulders, sides and front, 2 inch silver reflective striping with contrasting trim, sizes Small through 5X Large. Sold each. $1.71 over the non-breakaway RVZ40 for a vest that lets go when a rack or a truck does not.
Heat. Mesh is the answer, and a certified mesh vest is a certified vest: the RVZ40, RCZ21, RVHL40 and RVZ36 are all polyester mesh and all carry an ANSI class on our listings. For crews who want one garment instead of a vest over a shirt, the RTS21 Class 2 moisture-wicking T-shirt ($16.21) is rated Type R Class 2 and UPF 30+ on its own.
Cold and rain. The hi-vis layer has to be the outer layer, so in winter the vest becomes a jacket or an insulated vest. The RWVZ45 ($64.78) is a Class 2 vest with a 270g quilted lining and a reversible dark side; the RJ31 bomber ($78.77) is Class 3, "Waterproof per ANSI/ISEA 107-2020 with AATCC 127," with a zip-out fleece liner. Pair either with the RRWP31 Class E rain pants and the crew is Class 3 from the ankles up.
Sparks and arc flash. Two different products answer two different hazards, and the listings are blunt about which is which. The RVZ21SE self-extinguishing vest ($60.80 for a pack of 5) is a Class 2 mesh vest "for crews who need hi-vis near sparks and hot work," and the listing adds: "not designed for use in an arc flash or flash fire application." For electrical work the vest has to carry an arc rating. The RVZ52FR Class 2 ($79.90) and RVZ53FR Class 3 ($119.90) are modacrylic mesh vests with "an arc rating (ATPV) of 4.0 cal/cm² under ASTM F1506 and NFPA 70E Category 1," with flame resistant tape and trim. A standard polyester vest worn over FR clothing at an energized panel undoes the FR clothing, which is why the ANSI label rule in Question 3 exists.
Color and service life. ANSI/ISEA 107-2020 allows three background colors, per 3M: "fluorescent yellow-green, fluorescent orange-red and fluorescent red." Lime and orange are the two Pyramex offers; pick the one that contrasts with your building, your freight and your other crews' uniforms, and write it into the site rule so visitors can be told apart from staff at a glance. On service life, PIP's summary notes that the 2020 revision dropped the maximum wash cycle count from the care label, so there is no printed expiry. Retire a vest when the fluorescent fabric has faded, the tape has cracked or lifted, or the closures no longer hold, because the class is a count of material that still works.
Which safety vest should you buy?
Match the job to the line that describes it.
- Warehouse floor, dock and fenced yard, daytime or lit, no roadside work: Pyramex RVZ40 Class 2 ($6.90) or RVHL29 Class 2 ($5.57). Class 2 Type R exceeds the Type O Class 1 minimums the standard writes for off-road work and keeps the same vest legal when the worker steps onto a roadside. Buy the RVZ21 pack of 5 ($42.88) to outfit a crew in one order.
- Pickers and dock workers who work within arm's reach of forklifts, racks or conveyors: Pyramex RVHL40 Class 2 breakaway ($8.61), or the RCA25 ($12.64) if they also clip into a lanyard. The vest lets go before the equipment drags the wearer.
- Anyone who works on foot in a street or highway right-of-way, daytime: Class 2 Type R is the MUTCD 6C.05 floor and the flagger rule in 1926.201(a). Document the class choice in the 1910.132(d) assessment and name the person who made it.
- Night or low-light work, outdoor yards in winter, roadside work after dark, or anyone who stands sideways to traffic: Pyramex RVZ36 Class 3 ($19.10) or RVZ34 Class 3 ($20.26), or a Class 2 vest with RRWP31 Class E rain pants ($27.46). The MUTCD's own Guidance puts night flaggers in Class 3.
- Hot work, grinding, cutting: Pyramex RVZ21SE Class 2 self-extinguishing ($60.80 for 5). Not for arc flash or flash fire, per the listing.
- Electrical work at energized equipment: Pyramex RVZ52FR Class 2 ($79.90) or RVZ53FR Class 3 ($119.90), ATPV 4.0 cal/cm², ASTM F1506, NFPA 70E Category 1. Confirm the arc rating your 70E assessment calls for before you order.
- Visitors, temps for a day, a tour group inside a controlled building: Pyramex RV1 non-rated mesh vest ($77.95 for 12, about $6.50 each). It makes a visitor visible; it does not satisfy a hazard assessment that calls for an ANSI class, and it is never the vest for a roadside.
Every vest above is in our hi-vis safety vests collection, with Class 3 shirts, jackets and Class E pants in hi-vis workwear. If the job lands between two lines, call 1-800-794-1049, 8 AM to 4 PM Central, with where the crew works, whether any of it is after dark, and how many vests in each size. We will confirm the class, match a written price from another authorized dealer, and send a quote for approval, with volume pricing on crew orders through our request for quote page.
Frequently Asked Questions
What is the difference between a Class 2 and a Class 3 safety vest?
The amount of material and where it sits. Per 3M's summary of ANSI/ISEA 107-2020, a Type R Class 2 garment carries at least 775 sq in of fluorescent background fabric and 201 sq in of retroreflective tape; a Type R Class 3 garment carries at least 1,240 sq in and 310 sq in, and "Class 3 garments must have at least one retroreflective band encircling each sleeve." The minimum band width rises from 1.38 in to 2 in. In practice a Class 3 vest has short sleeves and a Class 2 vest does not. On Warehouse Gear Hub a Pyramex Class 2 vest runs $5.57 to $9.86 and a Class 3 vest runs $19.10 to $21.20.
Does OSHA require Class 2 or Class 3 safety vests?
For flaggers, yes, through the MUTCD: 29 CFR 1926.201(a) requires that "warning garments worn by flaggers, shall conform to Part 6 of the MUTCD," and MUTCD 6C.05 requires Class 2 or 3 for all workers in the right-of-way exposed to traffic, with Class 3 as Guidance for flaggers at night. For excavation crews, 1926.651(d) requires "warning vests or other suitable garments marked with or made of reflectorized or high-visibility material" without naming a class. For other highway work zone workers, OSHA's August 5, 2009 letter says high-visibility apparel is required under the General Duty Clause. Inside a warehouse, no OSHA standard names a class; the 1910.132(d) hazard assessment decides.
Do warehouse workers and forklift operators have to wear hi-vis vests?
Not by a rule that says so. OSHA's Powered Industrial Trucks eTool page on pedestrian traffic lists horns, mirrors, floor striping, speed limits and spotters and does not mention vests, and OSHA's warehousing guidance does not either. What applies is 29 CFR 1910.132(d): the employer "shall assess the workplace to determine if hazards are present, or are likely to be present, which necessitate the use of personal protective equipment," select PPE that protects and fits, and keep "a written certification that identifies the workplace evaluated." If that assessment finds people on foot sharing aisles and docks with forklifts, hi-vis is the obvious control and the employer provides it at no cost under 1910.132(h)(1). A Type R Class 2 vest is the practical floor for a warehouse that makes that call, and a Class 2 breakaway vest like the Pyramex RVHL40 ($8.61) is the one that also lets go if it snags.
What does Type R mean on a safety vest?
Roadway. 3M's summary of ANSI/ISEA 107-2020 defines "Type 'R' garments are for occupational workers who are exposed to roadway traffic," available in Class 2 and Class 3. Type O is "for occupational workers who are not required by the MUTCD 2009 edition to wear HVSA" and is Class 1 only; Type P "garments give additional options for fire, police, and EMS personnel" in Class 2 and 3 with less background fabric. The label shows a pictogram with the Type and Class. A Type R Class 2 vest is the garment the MUTCD minimum calls for, and every Pyramex vest on our site that lists a type lists Type R.
Does a Class 2 vest with Class E pants count as Class 3?
Yes, as an ensemble. Radians' summary of ANSI/ISEA 107-2020 states "Class 2 + Class E = Class 3," and Safety+Health magazine quotes Tingley Rubber's Brian Nutt: "the use of a Class 2 and Class E garment together are equivalent to the use of a Class 3 garment." The numbers line up: Class E adds 465 sq in of background and 109 sq in of tape, which is the gap between Class 2 (775 and 201) and Class 3 (1,240 and 310) per 3M. Class E pants worn alone are not Class 1, 2 or 3. On our site the Pyramex RRWP31 Class E rain pants are $27.46 and the RWB46 Class E insulated winter bib is $96.21.
Is a non-rated safety vest ever enough?
Only where no rule and no hazard assessment calls for an ANSI class. The Pyramex RV1 ($77.95 for 12) is listed as non-rated, with 1 in vinyl tape, under the 1.38 in minimum band width for Class 2. It is a visibility layer for visitors and one-day helpers inside a controlled building. It satisfies neither MUTCD 6C.05 for anyone in a right-of-way nor 1926.201(a) for a flagger, and if your written 1910.132(d) assessment selected Class 2 for the floor, handing out a non-rated vest is a gap between the paper and the practice.
How much does a Class 2 or Class 3 safety vest cost?
On Warehouse Gear Hub as of this writing, Pyramex Class 2 vests are $5.57 (RVHL29, hook and loop), $6.90 (RVZ40, zipper mesh), $8.61 (RVHL40, breakaway), $9.86 (RCZ21, X-back) and $42.88 for a pack of 5 RVZ21. Class 3 vests are $19.10 (RVZ36, all mesh), $20.26 (RVZ34, solid front) and $21.20 (RVZ38BR, breakaway). Class E rain pants are $27.46, arc-rated FR vests are $79.90 for Class 2 and $119.90 for Class 3, and the non-rated RV1 is $77.95 for a pack of 12. Under 29 CFR 1910.132(h)(1), required PPE is provided by the employer at no cost to employees.
Answer the four questions, then buy once
Pyramex Class 2, Class 3, breakaway, arc-rated and Class E hi-vis apparel, with the ANSI type and class on every product page and crew pricing by the pack.
Shop hi-vis safety vests →Questions on class, sizing a mixed crew, or a volume quote: call 1-800-794-1049 (8 AM to 4 PM Central) or email info@warehousegearhub.com.
