How to Choose a Concrete Washout Container: 4 Questions That Decide It (With EPA Rules and Real Prices)
A concrete washout container is chosen by four questions: whether your site falls under the federal construction stormwater rules that prohibit discharging washout water, whether a lined pit, a portable berm or a hauled roll-off bin fits the way your pours run, how many gallons the container has to hold between cleanouts, and where it sits and how it is run from the first truck to final disposal. On Warehouse Gear Hub, UltraTech's Economy Concrete Washout Berms run from $50.00 (30 x 30 inches, 50 gallons) to $92.00 (60 x 60 inches, 180 gallons), the one-piece 3512 berm (48 x 48 inches, 139 gallons) is $152.00, and the reusable drive-in RPE berms are $473.00 (8 x 10 feet, 598 gallons) and $499.00 (10 x 10 feet, 748 gallons). Every regulation quote below comes from the text of 40 CFR 450.21, 122.26 and 261.22 as published by the Government Publishing Office and from EPA's 2022 Construction General Permit and concrete washout fact sheet, every berm dimension and capacity comes from UltraTech's spec pages, and every price is our live listing as of this writing.
- Does the EPA require a concrete washout container?
- Question 1: Lined pit, portable berm, or roll-off bin?
- Question 2: How many gallons do you need?
- Question 3: Disposable or reusable?
- Question 4: Where does it go and how do you run it?
- Which concrete washout container should you buy?
- Frequently asked questions
Does the EPA require a concrete washout container?
It requires the result, not the product. The federal effluent guideline for construction sites, 40 CFR 450.21(e), opens with "The following discharges are prohibited:" and lists first, at (e)(1), "Wastewater from washout of concrete, unless managed by an appropriate control." The same list bans "Wastewater from washout and cleanout of stucco, paint, form release oils, curing compounds and other construction materials" at (e)(2), which is why one berm on a site ends up catching all of it. Paragraph (d)(1) adds the general duty to "Minimize the discharge of pollutants from equipment and vehicle washing, wheel wash water, and other wash waters."
The rule reaches any construction site that needs a stormwater permit. 40 CFR 122.26(b)(15)(i) defines small construction activity as "Construction activities including clearing, grading, and excavating that result in land disturbance" of one acre or more and under five acres, and (b)(14)(x) covers sites of five acres and up, including any smaller piece of "a larger common plan of development or sale" that "will ultimately disturb five acres or more." Disturb an acre and you hold a permit; hold a permit and 450.21(e)(1) is a condition of it.
EPA's own permit spells out what "appropriate control" means. The 2022 Construction General Permit (as modified, effective April 8, 2025 and expiring February 16, 2027) repeats the prohibition at Part 1.3.1, "Wastewater from washout of concrete, unless managed by an appropriate control as described in Part 2.3.4," and Part 2.3.4.a then requires you to "Direct wash water into a leak-proof container or leak-proof and lined pit designed so no overflows can occur due to inadequate sizing or precipitation." Part 2.3.4.b.i bars dumping liquid waste into "constructed or natural site drainage features, storm inlets, or receiving waters" and bars letting it be "disposed of through infiltration or to otherwise be disposed of on the ground," and 2.3.4.b.ii has you "Remove and dispose of hardened concrete waste consistent with your handling of other construction wastes." Part 2.3.4.c sets the siting rule: "Locate any washout or cleanout activities as far away as possible from receiving waters, constructed or natural site drainage features, and storm drain inlets," designate the areas, and wash out "only in these areas."
Your state construction permit and your SWPPP are the texts an inspector holds you to on site, and the state documents add detail the federal rule leaves open. Minnesota's washout guidance states "Liquid and solid washout wastes must be contained in a leak-proof container and cannot contact the ground" and requires a washout sign at each facility. Iowa DOT's Section 11,050 prohibits "Silt fence, unlined hay bales, unlined earthen embankments" as washout containment and sets a liner minimum of 10 mils. Read your state permit and your SWPPP before you read a product page; the four questions below are how you turn their words into a purchase.
Question 1: Lined pit, portable berm, or roll-off bin?
Every compliant washout is one of four things, and the choice turns on how many pours, how long the concrete phase lasts and whether a truck can reach the spot.
A lined pit is dug into the ground or built above grade from straw bales or lumber and lined with plastic. EPA's concrete washout fact sheet (EPA 833-F-11-006) shows one "made with hay bales and a plastic lining." The specs the states attach to it are what make it cost more than it looks: Iowa DOT requires "an impermeable plastic liner with a minimum thickness of 10 mils" below grade and "a double thickness of impermeable plastic liner with a minimum thickness of 10 mil per sheet" above grade, and Tennessee's EPSC handbook calls for a "minimum freeboard of four inches" on above-grade units and "12 inches for below-grade washout facilities." A pit does not move, a pump truck has a hard time reaching into it, and when it is full you clean it out with an excavator. It fits one place: a long project with heavy concrete volume, space to spare and equipment already on site.
A portable berm is the prefabricated version of the lined pit: a folding polyethylene tray, or a frame with a liner, that unfolds on the ground and holds 50 to 748 gallons. The EPA fact sheet describes this class as "portable, reusable, and easier to install than a hay bale washout pit." It is what we sell, and it is the right answer for the majority of sites because it costs between $50.00 and $499.00, folds flat, sets up without a machine and moves to the next pour. Its limits are capacity and durability: a 48-inch berm handles a day of chute rinses, not a week of pump-truck hoppers, and the lighter models are built for one job.
A roll-off bin is a steel container delivered by a washout service, swapped when full and hauled to a recycler. The fact sheet notes the "metal roll-off bin ... is designed to securely contain concrete washwater and solids." It holds the most, it is the only one of the four that someone else empties, and because it is rented it comes with delivery, a rental rate that runs for the whole concrete phase, disposal charges and the need for a roll-off truck to reach level ground near the pour. Choose it when the concrete phase runs for months and no one on the crew should be managing washout.
A chute-mounted box or bucket rides on the mixer and catches the chute rinse at the source. Iowa DOT lists an "on-vehicle chute washout system" as acceptable containment, and the fact sheet shows both a box and a bucket version. Capacity is a few gallons, the ready-mix supplier owns it, and it does nothing for the pump truck, the finishers' tools or the wheelbarrows, so most sites still need ground containment next to it.
| Option | What it costs you | Capacity | Best fit | Weak point |
|---|---|---|---|---|
| Lined pit (dug or straw bale) | Excavation or bales and lumber, 10 mil liner (double above grade per Iowa DOT), labor to build and to clean out | Whatever you dig, with 4 to 12 inches of freeboard held back | Long project, high volume, equipment on site | Fixed in place, pump trucks reach it poorly, cleanout needs a machine |
| Portable berm (what we stock) | $50.00 to $499.00 purchase, no rental clock, no delivery truck | 50 to 748 gallons per unit | Most sites: footings, slabs, driveways, repair work, satellite washouts on big jobs | You manage the fill level and the disposal; small models are single use |
| Roll-off bin (service) | Delivery, rental rate, disposal fee, swap fees | Largest of the four, set by the bin | Months of continuous concrete, no crew time for washout | Needs roll-off truck access and level ground; cost runs for the whole phase |
| Chute-mounted box or bucket | Supplied by the ready-mix company | A few gallons, chute rinse only | Supplement to ground containment | Does not catch pump hoppers, tools or wheelbarrows |
UV-resistant 10 mil polyethylene (LLDPE), 5 lb, "Unfolds for simple and quick set up in seconds," built-in tie-downs for a standard wooden pallet, compatible with mixers, pump trucks and wheelbarrows, per UltraTech. No separate liner to fit.
Question 2: How many gallons do you need?
Size to the washouts between cleanouts, then hold back a quarter of the tank. Chattanooga-Hamilton County's concrete washout BMP, citing Concrete Washout Systems, Inc. (2006), "estimates that 7 gallons of wash water are used to wash one truck chute" and that "50 gallons are used to wash out the hopper of a concrete pump truck." Those two figures are the sizing inputs. The EPA fact sheet supplies the cap: cleanout is due "When the washout container is filled to over 75 percent of its capacity," and Iowa DOT writes the same line as a requirement, "Clean out the concrete washwater containment area when it reaches 75% of the total capacity." So the usable volume of any container is three quarters of its rated capacity, and the fourth quarter is the freeboard that keeps a chute rinse or a rain shower from sending slurry over the wall.
Count the trucks, then the pump
A ten-truck slab pour with no pump is ten chute rinses, or about 70 gallons. The same pour through a pump truck adds one 50 gallon hopper washout, so 120 gallons. A week of footings with three trucks a day is 15 chutes, about 105 gallons, before anyone rinses a wheelbarrow. Compare those totals to the usable (75 percent) column below, which is our arithmetic on UltraTech's rated capacities, rounded down to whole gallons and whole washouts.
| Model we stock | Size and rated capacity, per UltraTech | Usable at 75 percent | Chute rinses at 7 gal | Pump hoppers at 50 gal | Price as listed |
|---|---|---|---|---|---|
| UltraTech 3515 Economy Model | 30 x 30 x 15 in, 50 gal, 5 lb | 37 gal | 5 | 0 | $50.00 |
| UltraTech 3516 Economy Model | 48 x 48 x 15 in, 140 gal, 9 lb | 105 gal | 15 | 2 | $69.00 |
| UltraTech 3512 one-piece berm | 48 x 48 x 14 in, 139 gal, 5 lb | 104 gal | 14 | 2 | $152.00 |
| UltraTech 3517 Economy Model | 60 x 60 x 12 in, 180 gal, 11 lb | 135 gal | 19 | 2 | $92.00 |
| UltraTech 3510 RPE Model | 8 x 10 ft (120 x 96 x 12 in), 598 gal, 29 lb | 448 gal | 64 | 8 | $473.00 |
| UltraTech 3511 RPE Model | 10 x 10 ft (120 x 120 x 12 in), 748 gal, 35 lb | 561 gal | 80 | 11 | $499.00 |
Subtract the rain
An open berm is a rain gauge with a large mouth. One inch of rain on a 48 x 48 inch footprint (16 square feet) is about 10 gallons; on the 10 x 10 foot RPE berm (100 square feet) it is about 62 gallons, using 7.48 gallons per cubic foot. That is why Part 2.3.4.a of the CGP names "precipitation" alongside "inadequate sizing" as a cause of overflow you have to design out, and why the EPA fact sheet says "Before heavy rains, the washout container's liquid level should be lowered or the container should be covered." If your pour schedule runs through a wet season, buy one size up or plan to tarp the berm between pours. Solids are the other thing that does not evaporate: the cement and sand settle and stay, so a berm that "holds 140 gallons" holds 140 gallons once, and less on every pour after that until it is cleaned out.
Width matters as much as volume
Chute rinse lands where the chute points, and a mixer chute swings wide. The Hamilton County BMP recommends washouts on larger sites be "at least 10 feet wide," which is the dimension of both RPE berms and is why they are built with removable sidewall supports so a truck can drive in. A 30-inch berm is a tool and wheelbarrow washout; a 48-inch berm catches a chute from a parked truck that is positioned with care; 60 inches and 10 feet give the driver room to miss.
Folds flat, 9 lb, ships with a "heavy-duty, 6 mil liner" that locks into slotted edges, rated for concrete washout, paint waste and other construction materials, per UltraTech. 105 usable gallons at the 75 percent rule: 15 chute rinses or two pump hoppers. The 30 x 30 inch 3515 is $50.00 and the 60 x 60 inch 3517 is $92.00.
Question 3: Disposable or reusable?
The three UltraTech lines are built to three different lifespans, and the price follows the lifespan.
Economy Model (3515, 3516, 3517): one pour, then it goes in the dumpster with the concrete. UltraTech's Economy Model page describes a berm with a "heavy-duty, 6 mil liner (included)" and "Specially designed slotted edges" that lock the liner in place, and its FAQ is plain: "We do not recommend using the berm more than one time." Disposal is the easy part: "Washout should be allowed to dry/harden. It can then be broken up and hauled away/disposed of." At $50.00 to $92.00 the Economy berm is the washout you buy by the case for a season of footings and driveways, one per pour, and the one you hand to a sub so the question of where the chute gets rinsed is settled before the first truck backs in.
3512 one-piece berm: thicker, no liner to fit, typically one use. UltraTech's 3512 spec page lists "UV resistant, 10 mil polyethylene (LLDPE) construction" in a single folded piece that "Unfolds for simple and quick set up in seconds," 139 gallons in a 48 x 48 x 14 inch footprint at 5 lb, with built-in tie-downs that secure it to a standard wooden pallet for handling and transport. On reuse the FAQ says "In some cases, it can be reused but typically it is a one-time use." The extra $83.00 over the 3516 buys the 10 mil wall (the same minimum Iowa DOT and the Hamilton County BMP set for a pit liner), one-piece construction with no liner seam to fail, and the pallet tie-downs. Pick it when the berm has to survive a few days of traffic around it, or when a pallet jack is how it leaves the site.
RPE Model (3510, 3511): reusable, drive-in, 30 mil. UltraTech's RPE Model page describes "Textured reinforced polyethylene (RPE)" that "holds up to heavy use and harsh jobsite conditions," set up with "Wire L-brackets" that "slide into built-in sleeves," and sidewall supports that "can be quickly removed, allowing trucks to drive directly into and out of the berm." It is listed as "Designed for repeated use from one jobsite to the next," and our listing specifies 30 mil material. The 8 x 10 foot 3510 holds 598 gallons at 29 lb and the 10 x 10 foot 3511 holds 748 gallons at 35 lb, both with 12 inch walls. At $473.00 and $499.00 the RPE berm costs about seven of the 3516s. A concrete contractor pouring weekly passes that break-even in two months, and gets a washout the pump truck can drive into instead of reaching over.
120 x 120 x 12 inches, 35 lb, textured reinforced polyethylene, wire L-bracket sidewalls that lift out so the mixer or pump truck drives in, built for repeated use, per UltraTech. 561 usable gallons at the 75 percent rule: 80 chute rinses or 11 pump hoppers. The 8 x 10 foot 3510 (598 gallons) is $473.00.
Question 4: Where does it go and how do you run it?
A berm placed badly is a violation with a receipt. These are the rules that govern the spot and the routine, with the agency that wrote each one.
Fifty feet from anything that drains. The EPA fact sheet says washout facilities "should not be placed within 50 feet of storm drains, open ditches, or waterbodies," and Iowa DOT makes it mandatory: "Locate concrete washout containment systems a minimum of 50 feet from proposed or existing storm sewer intakes, open ditches, or waterbodies." The CGP's Part 2.3.4.c phrases it as "as far away as possible" from receiving waters, drainage features and storm drain inlets. Put the berm on level ground, close enough to the pour that drivers use it, with a gravel approach if the ground is soft, and never in the low spot where the site drains.
A sign at the berm. Minnesota requires "a concrete washout sign" at each temporary washout facility; Iowa DOT says to "Clearly mark the location of the washout area and provide directions to truck drivers." The fact sheet's version is that signage is needed when the facility is not visible from the pour. A driver who cannot find the washout rinses at the gate.
Inspect daily and after rain, clean out at 75 percent. The fact sheet calls for inspection "daily and after heavy rains" for leaks and liner damage, and the 75 percent cleanout rule from Question 2 is the trigger for action. Iowa DOT: "Retain concrete washwater within the containment system until the water evaporates or is collected and disposed." If the liquid will not evaporate before the next pour, Minnesota's guidance is to vacuum it off and dispose of it in an approved manner, and to "Contact the local municipal wastewater treatment plant" for any special requirements before it goes anywhere.
Treat the liquid as the hazard, not the rock. The fact sheet describes washwater as "a slurry containing toxic metals" that is "also caustic and corrosive, having a pH near 12," against a safe range for freshwater life of 6.5 to 9. The federal hazardous waste line is close by: 40 CFR 261.22(a)(1) makes an aqueous waste hazardous for corrosivity (waste code D002) when it "has a pH less than or equal to 2 or greater than or equal to 12.5." A pH near 12 sits a half point under that line, which is the reason to test any washwater you haul off site rather than assume. The hardened solid is a different material: Iowa DOT allows it to be "disposed of as other non-hazardous wastes" or "broken up and used on the site for other appropriate uses," and the CGP sends it out with "other construction wastes." Keep paint, solvents and trash out of the berm, because a mixed load loses that easy disposal path.
Dispose of the berm separately. Tennessee's handbook notes that linings should be disposed of separately and not buried with the concrete, and Minnesota caps on-site burial of solids at "Up to 0.5 cubic yards." For an Economy or 3512 berm, the end of the job looks like this: let the water evaporate, break the slab out of the berm, send the concrete with the construction debris and the berm with the trash. For an RPE berm, break out the slab, hose the berm into the next washout, fold it and load it.
Which concrete washout container should you buy?
Match your pours to the line that describes them.
- Repair pours, tool and wheelbarrow rinse, one truck: UltraTech 3515 Economy Model ($50.00), 50 gallons, 37 usable, five chute rinses. Keep one in every truck.
- Residential footings, slabs and driveways, up to a dozen trucks between cleanouts, no pump: UltraTech 3516 Economy Model ($69.00), 140 gallons, 105 usable, 15 chute rinses. Buy a case and use one per pour.
- The same pours where the berm will sit several days or leave on a pallet jack: UltraTech 3512 ($152.00), 139 gallons, 10 mil one-piece, pallet tie-downs.
- Pours with a pump truck, or a wide chute swing on a tight pad: UltraTech 3517 Economy Model ($92.00), 60 x 60 inches, 180 gallons, 135 usable, two hoppers plus five chutes.
- Weekly pours, a pump truck that needs to drive in, or a central washout for a commercial site: UltraTech 3510 RPE ($473.00, 598 gallons) or UltraTech 3511 RPE ($499.00, 748 gallons). Reusable; pays for itself against single-use berms in about seven pours.
- Months of continuous concrete with no one to manage it: a roll-off washout service, with a 3516 or 3517 at each satellite pour the roll-off truck cannot reach.
All six berms are in the Stormwater Management collection. Warehouse Gear Hub is an authorized UltraTech dealer, and the berms ship direct from UltraTech. Case quantities for a season of pours, or a mixed order with inlet protection and dewatering bags for the same SWPPP, get a written volume quote: send your pour count, truck count per pour and whether a pump is involved to our request-for-quote page, or call 1-800-794-1049, 8 AM to 4 PM Central. We match prices.
Frequently Asked Questions
What is a concrete washout container?
A concrete washout container is a leak-proof tray, berm, pit or bin where ready-mix drivers rinse chutes, pump operators wash out hoppers and finishers clean tools, so the caustic, metal-bearing washwater and the cement solids are held until the water evaporates and the concrete hardens for disposal. EPA's 2022 Construction General Permit, Part 2.3.4.a, requires "a leak-proof container or leak-proof and lined pit designed so no overflows can occur due to inadequate sizing or precipitation." Portable polyethylene berms like UltraTech's hold 50 to 748 gallons and set up on the ground without equipment.
Does the EPA require a concrete washout area on a construction site?
Yes, on any site that needs a construction stormwater permit, which 40 CFR 122.26(b)(15) sets at one acre of land disturbance or more (and smaller sites that are part of a larger common plan of development). 40 CFR 450.21(e)(1) prohibits discharging "Wastewater from washout of concrete, unless managed by an appropriate control," and the Construction General Permit's Part 2.3.4 describes that control as a leak-proof container or lined pit, located as far as possible from drains and waters, with liquid waste kept off the ground and out of storm inlets. Minnesota's washout guidance adds a required sign at each washout facility, and Iowa DOT sets a 50 foot minimum from storm sewer intakes, ditches and waterbodies.
How big should a concrete washout container be?
Size it to the washouts between cleanouts, using about 7 gallons per truck chute rinse and about 50 gallons per pump truck hopper (Chattanooga-Hamilton County BMP, citing Concrete Washout Systems, Inc.), and count only 75 percent of the rated capacity as usable, because EPA and state specs call for cleanout at 75 percent full. A 140 gallon berm covers 15 chute rinses or two pump hoppers; a 748 gallon RPE berm covers 80 chute rinses or 11 hoppers. Add capacity for rain: one inch on a 48 x 48 inch berm is about 10 gallons, and on a 10 x 10 foot berm about 62 gallons.
Where should a concrete washout container be placed?
On level ground near the pour, where trucks can reach it without crossing active work, and at least 50 feet from storm drains, open ditches and waterbodies. EPA's concrete washout fact sheet gives the 50 foot figure as guidance and Iowa DOT's Section 11,050 makes it a minimum; the Construction General Permit requires washout "as far away as possible from receiving waters, constructed or natural site drainage features, and storm drain inlets." Post a sign so drivers find it, and put a gravel approach down if the ground is soft.
Can concrete truck washout water go into a storm drain?
No. 40 CFR 450.21(e)(1) prohibits the discharge of concrete washout wastewater, and Part 2.3.4.b.i of EPA's Construction General Permit says "Do not dump liquid wastes or allow them to enter into constructed or natural site drainage features, storm inlets, or receiving waters" and "Do not allow liquid wastes to be disposed of through infiltration or to otherwise be disposed of on the ground." The water has to stay in the container until it evaporates or is vacuumed off and disposed of under state and local rules.
Is concrete washout hazardous waste?
The liquid can be, and the hardened solid is not treated that way. EPA's fact sheet puts washwater at "a pH near 12," and 40 CFR 261.22(a)(1) classifies an aqueous waste as hazardous for corrosivity (code D002) at a pH "greater than or equal to 12.5," so washwater that is hauled off site should be pH tested before it is characterized. Hardened concrete is handled as ordinary construction waste: Iowa DOT allows it to be "disposed of as other non-hazardous wastes" or reused on site, and the Construction General Permit sends it out "consistent with your handling of other construction wastes."
How do you dispose of concrete washout?
Let the water evaporate in the container, then break up the hardened concrete and haul it with the construction debris or recycle it as aggregate. UltraTech's instruction for its berms is "Washout should be allowed to dry/harden. It can then be broken up and hauled away/disposed of." Dispose of a plastic liner or single-use berm separately from the concrete, do not bury it, and if the water will not evaporate before the next pour, vacuum it off and check with the local wastewater treatment plant on how to dispose of it, as Minnesota's guidance directs.
How much does a concrete washout container cost?
On Warehouse Gear Hub as of this writing, UltraTech's single-use Economy Model berms are $50.00 (30 x 30 inches, 50 gallons), $69.00 (48 x 48 inches, 140 gallons) and $92.00 (60 x 60 inches, 180 gallons); the one-piece 10 mil 3512 berm (48 x 48 inches, 139 gallons) is $152.00; and the reusable drive-in RPE berms are $473.00 (8 x 10 feet, 598 gallons) and $499.00 (10 x 10 feet, 748 gallons). A roll-off washout service charges delivery, a rental rate and disposal for the length of the concrete phase, and a dug pit costs excavation, a 10 mil liner and machine time to clean out.
Answer the four questions, then size the berm once
UltraTech Economy, one-piece and reusable RPE concrete washout berms from 50 to 748 gallons, with dimensions, capacity and material on every product page.
Shop washout berms →Case quantities and mixed SWPPP orders: request a quote, call 1-800-794-1049 (8 AM to 4 PM Central) or email info@warehousegearhub.com.
